IC693BEM341 可编程逻辑控制器 总线接口单元

基本细节:IC693BEM341 可编程逻辑控制器 总线接口单元

该IC693BEM341是工厂仪表协议 （FIP） 兼容模块，属于艾默生自动化的 90-30 系列可编程逻辑控制器 （PLC） 系列，以前由 GE Fanuc Automation 制造。该模块是对之前总线控制器的升级，因为IC693BEM341的数据速率为 2.5 MHz。该IC693BEM341特别带有三 （3） 个内置通信接口、两 （2） 个 9 针 D 外壳 FIP 总线连接器和一 （1） 个 RS485 通信接口，用于通过固件修改进行软件升级。该模块还安装了六 （6） 个 LED 状态指示灯，例如通道 1 的模块正常、运行、载波检测;通道 2 的载波检测;通道 1 启用传输，通道 2 启用传输。该 FIB 总线控制器模块设计用于通过 FIB 总线到 FIP 总线接口与各种设备连接，例如 90-70 系列 PLC;通过现场控制 I/O 模块通过 Filed 总线接口单元 （BIU） 的现场控制站;远程 I/O 通过 FIP 远程 I/O 扫描器模块和使用 FIP 接口模块的通用设备掉线。IC693BEM341需要 90-30 系列 CPU，版本为 8.0 或更高版本。对于配置，该模块需要使用手持式编程器 （HHP）、Windows 编程软件 IC641CTLxxx Release 2.0 或更高版本或 FBCLOAD 配置实用程序将有效配置下载到模块。该模块的附加功能包括显示固件版本、多达 1024 个布尔值的时间戳和模式 30（包括冗余、从 I/O 设备管理、时间戳、消息服务、MIPS 同步交换和外部配置接收）的功能。
IC693BEM341控制器是由GE Fanuc设计和制造的FIP总线控制器。这部分属于GE系列90-30。这种特定的控制器型号是对旧总线控制器的升级，它包括不同的创新功能。将此型号与 GE 340 控制器等旧型号进行比较时，它们在功能上是相同的，只是在新的 IC693BEM341 型号中提高了网络速度。GE Fanuc IC693BEM341 FIP 总线控制器是总线控制器的 2.5 兆赫兹版本。它也适用于固件版本 3.01。此总线控制器需要任何 IC693 PLC CPU 版本为 8.10 或更高版本。该现场总线控制器的另一个配置要求是它需要手持式编程器或 HHP。此 HHP 具有由 Windows 开发的编程软件，它应该是 2.0 或更高版本。必须使用 FBCLOAD 配置实用程序来配置控制器以在网络上正常运行。
IC693BEM341 FIP 总线控制器支持配置模式 30。此模式是配置模式 11 与以前的总线控制器版本相比的扩展，它为包括 I/O 嵌套、驱动器、PLC 和控制站在内的从属设备添加了冗余、管理和监控功能等不同功能。它还可以对布尔值进行时间戳，并通过 FIP 网络处理消息传递服务和外部配置的接收。GE Fanuc FIP 总线控制器中提供的一些更正是为了解决之前的问题，该问题导致 PLC CPU 在没有此类故障时报告的模块故障丢失。另一个已得到纠正的问题是，PLC应用的状态经常被错误地确定。

IC693BEM341

The IC693BEM341 is a Factory Instrumentation Protocol (FIP) compatible module that belongs to Emerson Automation’s Series 90-30 Programmable Logic controller (PLC) family and was previously manufactured by GE Fanuc Automation. This module is an upgrade over the previous bus controller, as the IC693BEM341 has a data rate of 2.5 MHz. The IC693BEM341 specifically comes with three (3) built-in communication interfaces, two (2) 9-pin D-housing FIP bus connectors, and one (1) RS485 communication interface for software upgrades via firmware modifications. The module is also equipped with six (6) LED status indicators, such as channel 1 module normal, operation, carrier detection; Carrier detection of channel 2; Channel 1 enables transmission and channel 2 enables transmission. The FIB bus controller module is designed to connect to various devices, such as 90-70 series PLCS, via the FIB bus to FIP bus interface; Field control station via field control I/O module via field bus interface unit (BIU); Remote I/O The FIP remote I/O scanner module and common devices using the FIP interface module are disconnected. The IC693BEM341 requires a 90-30 series CPU with version 8.0 or later. For configuration, the module needs to download the valid configuration to the module using a handheld programmer (HHP), Windows programming software IC641CTLxxx Release 2.0 or later, or the FBCLOAD configuration utility. Additional features of the module include the ability to display firmware versions, time stamps of up to 1024 Booleans, and mode 30, including redundancy, slave I/O device management, time stamps, message services, MIPS synchronous exchange, and reception of external configurations.
The IC693BEM341 controller is a FIP bus controller designed and manufactured by GE Fanuc. This part belongs to the GE series 90-30. This particular controller model is an upgrade over the old bus controller and it includes different innovative features. When comparing this model with older models such as the GE 340 controller, they are functionally identical except for the increased network speed in the new IC693BEM341 model. The GE Fanuc IC693BEM341 FIP bus controller is a 2.5 MHZ version of the bus controller. It is also available with firmware version 3.01. This bus controller requires any IC693 PLC CPU version 8.10 or later. Another configuration requirement for this fieldbus controller is that it requires a handheld programmer or HHP. This HHP has programming software developed by Windows and it should be version 2.0 or later. The FBCLOAD configuration utility must be used to configure the controller to function properly on the network.
The IC693BEM341 FIP Bus controller supports configuration mode 30. This mode is an extension of Configuration Mode 11 compared to previous versions of the bus controller, which adds different features such as redundancy, management, and monitoring functions to slave devices including I/O nesting, drives, PLCS, and control stations. It can also timestamp Booleans and handle the reception of messaging services and external configurations over the FIP network. Some of the corrections provided in the GE Fanuc FIP bus controller are designed to address a previous issue that caused the PLC CPU to lose module failures reported when there were no such failures. Another problem that has been corrected is that the status of PLC applications is often incorrectly determined.

如果您需要查询或购买，请将产品型号发送到我的电子邮件或直接致电我

销售经理:何经理

手机: + 86 18005021035

邮箱: 18005021035@163.com

与成都阳光熹禾合作我们提供一流的服务，实现更快的速度，交付多样化的零件!

1.在24小时内及时回复您

2.交货时间快

3.最好的服务，合理的价格

4.在生产线上工作多年，有良好的口碑

▲更多相关型号: IC693BEM341 可编程逻辑控制器 总线接口单元