PM860 ABB 控制器模块

ABB PM860 AC 800M控制器模块AC 800M控制器和所有模块的通信接口
AC 800M是一系列轨装模块，由CPU、通信模块、电源模块和各种附件组成。有几个CPU模块可供选择，从中等处理器能力和低成本到高处理器能力和支持完全冗余。
PM860A控制器的底板有两个RJ45以太网端口(CN1、CN2)用于连接到控制网络，以及两个RJ45串行端口(COM3、COM4)。其中一个串行端口(COM3)是带有调制解调器控制信号的RS-232C端口而另一个端口(COM4)则被隔离并用于连接配置工具。
简单DIN轨道连接/卸料程序，使用唯一的滑道&锁机构。所有base plates都有唯一的以太网地址，每个CPU都有一个硬件标识。地址可以在连接到TP830 base plate的以太网地址标签上找到

PM860

PM851AK01-EA控制器的底板有两个用于连接控制网络的RJ45以太网端口(CN1、CN2)和两个RJ45串行端口(COM3、COM4)。其中一个串行端口(COM3)是带有调制解调器控制信号的RS-232C端口，而另一个端口(COM4)是隔离的，用于连接配置工具简单的DIN导轨连接/拆卸程序，使用独特的滑动和锁定机制。所有基板都有一个唯一的以太网地址，为每个CPU提供一个硬件标识。该地址可在TP830底板上的以太网地址标签上找到。

特点和优势

可靠性和简单的故障诊断程序

模块化，允许逐步扩展

IP20级保护，无需外壳

控制器可以用800xA控件生成器进行配置

控制器具有完全EMC认证的PM856控制器模块

基于最佳通信连接标准的硬件(以太网、PROFIBUS DP等)。)

PM860

ABB PM860 AC 800M controller module Communication port between the AC 800M controller and all modules
The AC 800M is a series of rail-mounted modules consisting of a CPU, communication module, power module and various accessories. There are several CPU modules to choose from, ranging from medium processor power and low cost to high processor power and support for full redundancy.
The baseplate of the PM860A controller has two RJ45 Ethernet ports (CN1, CN2) for connecting to the control network, and two RJ45 serial ports (COM3, COM4). One of the serial ports (COM3) is the RS-232C port with the modem control signal while the other port (COM4) is isolated and used to connect to the configuration tool.
Simple DIN rail connection/discharge procedure with unique slide & lock mechanism. All base plates have a unique Ethernet address, and each CPU has a hardware ID. The address can be found on the Ethernet address label connected to the TP830 base plate

The baseboard of the PM851AK01-EA controller has two RJ45 Ethernet ports (CN1 and CN2) and two RJ45 serial ports (COM3 and COM4) for connecting to the control network. One of the serial ports (COM3) is an RS-232C port with a modem control signal, while the other port (COM4) is isolated and is used to connect the configuration tool’s simple DIN rail connection/removal procedure using a unique sliding and locking mechanism. All baseboards have a unique Ethernet address, giving each CPU a hardware identity. This address can be found on the Ethernet address label on the TP830 baseboard.

Characteristics and advantages

Reliable and simple troubleshooting program

Modular, allowing for gradual expansion

IP20 protection, no case required

The controller can be configured with the 800xA control generator

Controller with fully EMC certified PM856 controller module

Hardware based on the best communication connectivity standards (Ethernet, PROFIBUS DP, etc.).

PM860